FS: Insert holders, 3 batches (small, medium, larger)

[aribert]

Thinning the herd. I have a few too many insert holders - have bought several odd lots at auction for the random insert holders contained there in. Insert holders are either duplicates or require sizes/styles of inserts that I don't use. Listed in 3 batches: 3/8 and 1/2 inch shank, 5/8 & 3/4 inch shank (including ones milled to size) and 1 & 1.25 inch shank. NOTE: I have more images of each holder available (that I can furnish if requested) since I am anticipating ending up listing a number of them on eBay eventually. 15% off for purchases of 3 or more. Combined shipping for multiple holders. For the smaller holders, send me your ZIP and I will check to see if shipping is less than $9.75 padded envelope. PayPal or check/MO. Shipping delayed until check/MO clears.

Small insert holders:
A. Valenite SD-TMR-8-3 1/2 inch shank, USA, I already have several of this size threading holder, $12.50 + shipping
B. SHARS SDJCR 3/8" includes (5) inserts that appear to be new, $15 + shipping
C. Mitsubishi (based on the logo on the tool) STGC L082.5 1/2 inch shank $12.50 + shipping
D. ACRA BL-8 SHCS looks out of place, 1/2 shank, $7.50 + shipping
E. SHARS SWGCR 3/8" looks new, no set screw clamp marks or wear marks $12.50 + shipping
F. Circle Machine QSBIW-500-6-3R 6 inch long , 1/2 inch dia bar, thru hole coolant, USA $25 + shipping
G. Valenite PSBNR-1212-09 Looks new, shelf rash but no set screw clamp marks or wear marks $12.50 + shipping

More images in the next post

 

[aribert]

Balance of images for the lot of smaller insert holders:

 

[aribert]

5/8 and 3/4 shank insert holders: shipping via USPS padded envelope at $9.75

AA. brand? NRS 12-3B top notch 3/4 shank, USA $20 + shipping
BB. Valenite VLSR 123B USA, 3/4 shank milled to 5/8. I have 4 RH topnotch but needed a LH, I did a lot of carving on this holder to make it work for a project. $12.50 + shipping
CC. SHARS LW 5/8" threading $10 + shipping
DD. Valenite PTMR-12-43 B Groove/threading. I used a turning insert to check clamp function - insert clamps in place even though post looks to be curved away from clamp, insert looks to be 1/2 IC, I use smaller and larger but not this size insert. $15 + shipping
EE. Valenite HP-CLR-12-4 MCLNR-12-4 3/4 shank milled to .67 in. $15 + shipping
FF. Carboloy MCLNR-12-4B 3/4 shank milled to .65 in. $15 + shipping
GG. Valenite PSBNR-1616-09, USA Like new - no screw clamp marks or wear marks $15 + shipping
HH. Valenite PTGNL-1616-16, USA Like new - no screw clamp marks or wear marks $17.50 + shipping.
II. Valenite PTGNL-1616-16, USA $15 + shipping
JJ. Carboloy MTANL-12-3 $17.50 + shipping
KK. TMX-Pafana MTJNR 10-3B 5/8 shank Like new - no screw clamp marks or wear marks $17.50 + shipping.
LL. SHARS SDJCR 5/8" $15 + shipping
MM. SHARS SCLCL 5/8" $15 + shipping
NN. Valenite Econ-O-Groove VDBA-125-18. 1 in. shank milled to 3/4, 3 position shank, USA $20 + shipping

 

[aribert]

more images of 5/8 & 3/4 inch insert holders

 

[aribert]

more images of 5/8 & 3/4 inch insert holders

 

[aribert]

more images of 5/8 & 3/4 inch insert holders

 

[aribert]

final batch of images of 5/8 & 3/4 inch insert holders

 

[aribert]

Larger insert holders, shipping via USPS padded envelope at $9.75:

V. brand? 1 1/4 shank, LS-20-5, appears to be 5/8 IC, chipped corner on seat $10 + shipping
W. Kennametal (label missing) KGSPR 16 shank: 1 in high x 1 1/4 wide. NOTE: Tool holder has been repaired - look at images $10 + shipping
X. Valenite SD-TMIL-16-4 groove/thread, 1 in shank, screw head appears too large $17.50 + shipping
Y. Kennametal (missing label) DCLNL-165C, 1 in. shank $15 + shipping
Z. Valenite VDBS-16, VDBA-125-180-LA Econ-O-Groove, Note: wear/damage on tip of toolholder under insert. 1 in. shank. Includes 2 grooving inserts, $20 + shipping

 

[aribert]

Final batch of images:

 

[paulsomlo]

I'll take A and F.

 

[aribert]

paulsomlo:
PM sent

 

[aribert]

A & F sold